Classification:Shot Blasting Equipment
Device name:Roller pass type shot blasting machine STR-1040P11-4
Browse times:188
Release date:2020-03-24
Comparison of shot blasting process
Comparison before and after shot blasting
Product description
① The shot blasting room is made of an all-manganese steel fuselage, which has sufficient rigidity and resistance to impact, and the fuselage is guaranteed to be not bad for 20 years. Inside the machine body is a double-layer 10mm wear-resistant manganese steel protective plate, which is locked by a high-wear-resistant nut, and there are double-opening inspection doors on the opposite side, which facilitates the maintenance and replacement of the shot blasting room, which greatly improves the maintenance.
② The rollers in the shot blasting room that are subjected to shot blasting are equipped with high-chromium molybdenum special iron wear-resistant sheaths that can be easily replaced. The roller table adopts variable frequency speed regulation, and the whole line can be conveyed quickly and slowly;
③Multi-layer sealing devices are set on both sides of the shot blasting chamber to prevent zero leakage of shot blasting during shot blasting;
④ A grating sensing device is installed at the feeding port of the shot blasting chamber. When the grating senses the parts, the shot blasting machine will start delaying and start the shot blasting operation. When no parts are detected in the shot blasting chamber, the shot blasting system will stop the throwing. Pill operation to prevent air throwing;
⑤ The equipment is equipped with 4 or 8 11kw high-performance throw heads, equipped with ABB motors. The uniformity of shot blasting is better, the cleaning efficiency is higher, and the overall energy consumption is lower;
⑥ Venturi wet-type dust collector is adopted, which is a new generation of dust collector developed by S & P Company. It is fireproof and explosion-proof, without any spare parts, and without any maintenance costs in the later period. The dust emission is less than 20mg / m³.
Comparison of shot blasting process
A. Installation instructions:
During installation, compare the general drawing of the equipment, place the main unit on the prepared foundation, fasten it with bolts, and install the upper part of the hoist to the main unit with bolts.
Install electrical conduit and complete wiring according to electrical drawings such as electrical schematics and interconnection diagrams
Place the spirit level on the bottom surface of the hopper, combine the base of the feeder, add the gasket and level it, and then tighten the bolt connecting the anchor bolt to the cleaning room
B. Commissioning instructions:
Adjust the position of the orientation sleeve opening
Adjust the shot supply valve and the amount of shot blasting according to the current display
Adjust the position of the counterweight to make the shot form a uniform waterfall
Adjust the upper pulley of the hoist to prevent misalignment of the belt
Adjust the sorter pipeline valve to achieve the separation effect
C. Equipment training content description:
Institutional performance and routine maintenance of equipment
Inspection method of wearing parts: replacement standard, cycle and method
Equipment operating procedures, technical requirements and methods for safe operation debugging
Roller pass type shot blasting machine STR-1040P11-4 | ||
Serial number | Model parameter configuration | Economy 丨 Standard |
1 | Equipment application | Various profiles / steel plates / round bars |
2 | Dimensions L * W * H (mm) | 14200*5500*6200 |
3 | Feed opening size: rotation diameter * high(mm) | 1000*400 |
4 | Single roll load(kg) | 500 |
5 | Conveying speed (m / min) | 0.5-5 |
6 | Dust emission(mg/m³) | ≤50丨≤10 |
7 | noise(db) | ≤85丨≤80 |
8 | Total equipment power (KW) | 77.5丨81.6 |
9 | Compressed air loss (m / min) | 0.5 |
Serial number | Model parameter configuration | Economy 丨 Standard |
1 | Shot blasting room full manganese steel body | ●丨● |
2 | Spiral pusher fault alarm system | ●丨● |
3 | Elevator shot recycling fault alarm system | ●丨● |
4 | Sprocket chain + roller conveyor | ●丨● |
5 | DC-12 Cartridge Dust Collector | ● |
6 | SWDC-100Wet dust collector | ● |
7 | Q11Shot blaster | ● |
8 | P11Full machine plus shot blasting machine | ● |
9 | Frequency conversion speed regulation of conveying system | ●丨● |
10 | Incoming and outgoing grating sensor | ●丨● |
11 | Semi-automatic flow control system | ● |
12 | Automatic flow control system | ● |
13 | Shot purge system | ●丨● |
14 | Shot blasting machine frequency control | ● |
15 | Electric cabinet air conditioner | ● |
16 | Storage bin alarm system | ● |
17 | Automatic feeding system | ● |
18 | Random Accessories | ○丨○ |